Grasshopper

algorithmic modeling for Rhino

Xylinus

ADDON

Component Index > Xylinus

Core
Filament
Syringe
DLP

Core

Center Print on Print Bed
Moves the input geometry to the center of the print bed as determined by the input printer dimesions
Config Setting
If an individual specific setting is input in S, it will be returned
Curve Infill
Take the given curve and creates an infill (based on the extrusion width and infill ratio) of the curve as a polyline
Curve to G Code
Converts a cureve into g code to 3D print with a standard filament based printer
Curve with Infill
Outputs polyines for W walls and infill at I density
Curves with Infill Compound
offsets curves by 1/2 the extrusion witdth
Offset In
Offsets curves inward
Offset Out
Offset curves outward
Offset Complex
Offset curves, with automatic detection of internal vs
Offset Compound
Contains a cluster of Grasshopper components
Print Log
saves info about the print into a Google Sheet
Slice Walls with Infill Compound
Slices geometry and offsets perimeters by 1/2 the extrusion witdth
Slice Walls with Infill
Slices input geometry and outputs polyines for W walls and infill at I density
Slice
Slice geometry based on layer height ( directly or from a Xylinus Config)

Filament

Config - Filament
This component holds the primary configurations needed for 3D printing on a standard filimant-based printer
Config - Filament jimmi PLA
Double-click to edit this blank starter config
Extrusion Rate Calculator
calculate basic extrusion rate as factored by the cross section area of the filament and that of the print extrusion
G Code Start - Filament
G code to begin the 3D print
G Code End - Filament
G code to end a 3D print
G Code Merge - Filament
Merge gcode with start and end gcode
Print Curve - Filament
Converts a curve into g code to 3D print with a standard filament based printer
Print Curve with Blob and Drool - Filament
extrudes a given amount of filament (Blob) at each point and a modified amount of filament (Drool) in between points
Print Curve with Infill - Filament
Slices input geometry and renerates G Code to print [W] walls and infill at [I] density
Print 3D - Filament
Slices input geometry and renerates G Code to print [W] walls and infill at [I] density

DLP

Black Out
creates a black out surface
Config - DLP
This component holds the primary configurations needed for 3D printing with an a DLP projector to do SLA
Config - DLP BUGSS
Config DLP BUGSS
DLP Slice
Slice geometry based upon a Xylinus DLP Config
G Code Start - DLP
G code to begin the 3D print
G Code End - DLP
G code to end a 3D print
GC Send
Sends G Code to the printer
Print DLP
Generate the G Code and synch it with the projected slices
Projector Window
Opens a floating viewport, maximizes it to the projector display, and zooms to the supplied calibration geometry
Z Move G Code
Generate the G Code to move the Z platform of the printer

Syringe

Config - Syringe M Codes
This configures the M Codes for pneumatically controlling a syringe
Config - Syringe
This component holds the primary configurations needed for 3D printing on a standard filimant-based printer
Config BUGSS_S M Codes
Contains a cluster of Grasshopper components
Config BUGSS_S
This component holds the primary configurations needed for 3D printing on a standard filimant-based printer
G Code Start - Syringe
G code to begin the 3D print
G Code nd - Syringe
G code to end a 3D print
Print Curve - Syringe
Converts a curve into g code to 3D print with a syringe based printer
Print Curve with Infill - Syringe
Slices input geometry and renerates G Code to print [W] walls and infill at [I] density
Print 3D - Syringe
Slices input geometry and renerates G Code to print [W] walls and infill at [I] density

© 2018   Created by Robin Rodricks and Andrew Heumann.   Hosted by

Badges  |  Report an Issue  |  Terms of Service